Maxim RRFP1A/T Bedienungsanleitung Seite 10

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 39
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 9
Single-/Dual-Band 802.11a/b/g
World-Band Transceiver ICs
AC ELECTRICAL CHARACTERISTICS802.11a Tx Mode (MAX2828/MAX2829)
(MAX2828/MAX2829 evaluation kits: V
CC
= +2.7V, f
OUT
= 5.25GHz, f
REFOSC
= 40MHz, SHDN = TXENA = CS = high, RXENA = SCLK
= DIN = low, R
BIAS
= 11k, 100mV
RMS
sine and cosine signal (or 100mV
RMS
, 54Mbps IEEE 802.11a I/Q signals wherever OFDM is
mentioned) applied to baseband I/Q inputs of transmitter, registers set to default settings and corresponding test mode, T
A
= +25°C,
unless otherwise noted.) (Table 4)
PARAMETER CONDITIONS
MIN
TYP
MAX
UNITS
TRANSMIT SECTION: Tx BASEBAND I/Q INPUTS TO RF OUTPUTS
802.11a low-band mode
4.900 5.350
RF Output Frequency Range, f
RF
802.11a high-band mode
5.470 5.875
GHz
2% EVM -5
Output Power
54Mbps 802.11a OFDM
signal
B6:B1 = 111100 -6.5
dBm
Output Power (CW)
V
IN
= 100mV
RMS
at 1MHz I/Q CW signal, B6:B1 =
111111
-4.5
dBm
f
RF
= 4.9GHz -6
f
RF
= 5.35GHz -0.5
Output Power Variation Relative
to 5.25GHz
f
RF
= 5.875GHz -1
dB
Output Power Range B6:B1 = 111111 to B6:B1 = 000000 30 dB
Carrier Leakage Without DC offset cancellation -27
dBc
Unwanted Sideband Suppression
Uncalibrated -51 dBc
Tx Output ACP
Measured with 1MHz resolution bandwidth at 30MHz
offset from channel center (B6:B1 = 111100), OFDM
signal
-80
dBm/
MHz
RF Output Return Loss With external 50 match -16 dB
4/5 x f
RF
-55
6/5 x f
RF
-64
7/5 x f
RF
-65
RF Spurious Signal Emissions
B6:B1 = 111100,
OFDM signal
8/5 x f
RF
-49
dBm/
MHz
Nominal mode 12
Turbo mode 1 18
Baseband -3dB Corner
Frequency
(see the Lowpass
Filter Register
Definition section)
Turbo mode 2 24
MHz
Baseband Filter Rejection
At 30MHz, in nominal mode (see the Lowpass Filter
Register Definition section)
60 dB
Minimum differential resistance 60 k
Tx Baseband Input Impedance
Maximum differential capacitance 0.7 pF
TRANSMITTER LO LEAKAGE AND I/Q CALIBRATION USING LO LEAKAGE AND SIDEBAND DETECTOR (SEE THE Tx/Rx
CALIBRATION MODE SECTION)
Tx BASEBAND I/Q INPUTS TO RECEIVER OUTPUTS
Output at 1 x f
TONE
(for LO
leakage = -29dBc), f
TONE
=
2MHz, 100mV
RMS
-4.5
LO Leakage and Sideband-
Detector Output
Calibration register,
D12:D11 = 1, A3:A0
= 0110
Output at 2 x f
TONE
(for sideband
suppression = -40dBc), f
TONE
=
2MHz, 100mV
RMS
-14.5
dBV
RMS
Amplifier Gain Range D12:D11 = 00 to D12:D11 = 11, A3:A0 = 0110 26 dB
Lower -3dB Corner Frequency 1
MHz
MAX2828/MAX2829
10
Maxim Integrated
Seitenansicht 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 38 39

Kommentare zu diesen Handbüchern

Keine Kommentare